Hello everyone. Could someone tell me more about gluing settings to make with one edge pick up glue two sides of panel? I searched everywhere but could not find settings for that. And one more question, i need to cut board with ceramic cover, i have tried lot of different type cutters but cutting quality is real bad. Maybe someone could help with advice?
Centateq E-500
-
-
haben schon einen auftrag mit keramikbeschichteten platten gemacht und nur mit diafräsern im gegenlauf eine gute qualität erhalten.
sägen ging damals gar nicht von der qualität.
die löcher haben wir damals alle gefräst und nicht gebohrt.
-
haben schon einen auftrag mit keramikbeschichteten platten gemacht und nur mit diafräsern im gegenlauf eine gute qualität erhalten.
sägen ging damals gar nicht von der qualität.
die löcher haben wir damals alle gefräst und nicht gebohrt.
Um welche Platten handelt es sich da? Hab ich noch nie gehört
-
vom aufbau wie eine compactplatte nur die oberste schicht ist mit einer keramikschicht überzogen.
wir in laboren mit sehr hoher chemischen beanspruchung benötigt.
wurde damals ich glaube aus den niederlanden impotiert und vom kunden bereitgestellt.
-
Can you maybe give examples where and what kind of milling cutters you used? Maybe i can get them from leuco?
-
ich habe diese fräser im einsatz gehabt reichten vollkommen aus.
-
I would use tools like these
-
ich habe diese fräser im einsatz gehabt reichten vollkommen aus.
Hattest du da keine leichten übergäge wo die unterschiedlichen schneiden waren?
-
LEUCO - DIAMAX High-Performance Shank-Type Cutters DP - Z=2+2Tool selection made easy: With filters for tool dimensions, your machine type/manufacturer or your material to be machined, you will receive your machine tools…www.leuco.com
i tried this type of cutters and changed cutting options starting with n/min and feed as well but quality was awful
-
Hattest du da keine leichten übergäge wo die unterschiedlichen schneiden waren?
sicht kante habe ich damals mit dem schleifpapier korn 150 nachgeschliffen.
möglich wäre natürlich auch mit durchgehender schneide zu fräsen, hatte damals nur den fräser zur hand.
-
What feeds and speeds you run the tool? And whats was the problem?
-
LEUCO - Finishing Cutters VHW - ecolineTool selection made easy: With filters for tool dimensions, your machine type/manufacturer or your material to be machined, you will receive your machine tools…www.leuco.com
Best result i get with this type of cutters but still it is not so good how i need because we need to finish edges with ABS and there is lot of small breakthroughs
-
I run tool speed with 12000n/min and feed was 1-1,5m/min
-
-
Ok maybe are the breakthroughs from the Ceramic cover, i never cut ore mill material like this.
We have a lot of HPL Material in 8-12mm and the tools i sent the link are really good for this materials.
I think 12000n/min is a little bit low try 16000n/min and maybe 5m/min.
-
ok thats not good.
Are you sure that the z-height is correct? The tool has a changing axis angle and the plate is so thin that you have to go further down in z
-
This is upper part for plate and yes i tried different z levels, this plate contains magnetic cover on face part so i guess this is the main problem why usual milling makes breakthrough. now i ordered new milling cutter which is special made for magnetic boards with ceramic cover, will make some tests and then will see if it is working. I heard about hpl with ceramic cover and no one have problems with that but this is little bit different material with ceramic cover
-
do you know what the material is called? and which manufacturer is it from?
-
Just a minute i will send data sheet and manufacturer
-
-
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!