Posts by samiki

Hello!

For depth specifications and contour processing does not work in a-angle trimming, as it was already told here before.

support macro:

• Vertical drilling

• Horizontal drilling

• Drilling from below

• Drilling with A angle

• Polygon path trimming

• Vertical sawing with programmed depth

• Vertical pocket trimming

• Pocket trimming with A angle

• Pocket trimming from below

• Horizontal pocket trimming

• Free-form pocket trimming

Vertical contour macros:

• Vertical trimming

• Trimming from below

• Vertical trimming with C axis

• Vertical trimming, traced

If you want to check a possible collision, you should do it with a machine simulator or woodmotion program.

-Sami

Hello!

Make a new component where you have both saws (left/right) and tensos placed in them ready. This way you can place the finished full component with 0 values and just choose which cut you want to make.

-Sami

Hello!

Here is the file with which I did the test and everything worked.

-Sami

Hello!

Minimum and maximum can be 0 and everything should work. This is how it can be when a 5-axis machine is used, and not an aggregate. In the example I had the values 0 for both and everything works.

-Sami

Hello Sebastian!

There is probably nothing wrong with the program. At least check the minimum and maximum A-tilt of the tool. I also noticed that at least the latest version of woodWOP (7.2.92.0 OR 8.0.681.0) requires that the dust hood must be set in the upper position. In automatic mode, gives an error and a note about the height of the dust hood. This error / message probably always comes from nc changes where the A or Z position is changed. This auto height adjustment has come since version 7.2.84.0 or 8.0.516.0

-Sami

Hello!

Is this what you are looking for? In the example, you can set the "yc" or "yd"-measurement to both ends separately and the chamfer of the corners is calculated accordingly. I didn't do the calculation for the "y" zero edge, but it goes with the same formula as for the top edge. Note that this was done on a Saturday night... There may be some mistakes in the formulas... but it's very close

-Sami

Hello!

You can add part variables to the profile used in the bpp5 program. But remember that the variables only take the dimensions of the piece. Changing the values of the variables does not change the geometries or machinings imported in dxf import. Geometries and machinings are fixed to absolute values on import, so changing variables does not affect them.

You can add a clamping component when you use a block in the dxf-file and give it the layer name AK500 or ZP500

-Sami

Hello!

Why do you need so many variables? For example, with two variables that both have two characters (00-99) you already get 10,000 different options.Attached is a clock face where you can control the time with three variables and thus you can set every second of the day, with only three variables. There will be 24*60*60 = 86400 options.

I have understood that with a Qr code it is possible to load, for example, 128 variables, but then the reading is done in a different way. The QR code then contains the name and value of the variable. It is probably of the form program path; variable1=123; variable2=456; variable3=789... etc

I recommend asking Homag about this

-Sami

Hello!

If I understood correctly, you are looking for the following?

First, you need at least three different optimization parameters. One for less than 69mm, then another for 69-100mm and the third for larger 100mm.

You make the necessary changes for each of these under strips in the settings.

Then you need optimizing parameters in the information box.

After this, you still divide the cutting list into different lists with the difference of the optimizing parameter.

Finally, you make the cutting rules and enable it in the parts list, so that the change appears in the cutting list

-Sami

Hello!

i'm running version 5.0.62 so I think you only need the latest version.

-Sami

Hello!

I think you can change that even in the basic version. The weather can be found in the "Options" section and under the "MPR header options"

-Sami

Quote from Gschloar

Kann es sein das mit der Testversion vom DXF-Import Proffesional keine Profile gespeichert werden können?

Wenn ich auf speichern oder speicher unter gehe passiert bei mir nichts.

Hello!

unfortunately, recording always requires a valid license

-Sami

Hello!

a simple test with a simulator.

pocket size 150*25mm and depth 80mm
in four steps.

with contours 35sec
horizontal pocket 41 sec

From what I know, quite a few larger factories use standard horizontal pockets or A-angle pockets if they have a five-axis machine, often is.
The horizontal pocket and the A-angle pocket have a small difference in terms of approaches.

What the speed comes from is precisely the number of units in the machines. The machines usually have two or even three milling units, so tool changes do not take time.

-Sami

Hello!

Here is an explanation of the difference GRP / WCP

-Sami

Hello!

Here are a couple of pictures showing how it works. The variable "kulma" in question controls the new level in the component.

-Sami

Hello!

yes, that rotation is already possible for the component, even in the ww5 version. The component should only be made to a new level, then only the Z rotation of the new level is controlled by the variable.

-Sami

Hello!

Yes you can change the A-angle using the technique macro in the spline line. If you want to change it often, the shape must be made from several different spline lines.

-Sami

Hello!

Those in the pictures are optimization parameters. You should change the saw parameter, if you want the extra trim removed.

See pict.

-Sami

Hello!

if you mean by the arrows the point where the saw has trim and you want it removed, set the trim to zero in the saw parameters.

-Sami

Hello!

If the unprocessed part is created correctly and used as a 3d model, it should come into motion automatically.

See pictures.

The unprocessed part should be visible in woodWOP with brown lines, so it stands out clearly.

-Sami